<td id="0mk8k"><table id="0mk8k"></table></td>
  • <xmp id="0mk8k">
  • <menu id="0mk8k"><strong id="0mk8k"></strong></menu><xmp id="0mk8k"><menu id="0mk8k"></menu><nav id="0mk8k"></nav>

    濟南誠耐

    濟南誠耐金屬制品有限公司

    精湛的技術力量、完善的設計服務團隊,真誠為您提供專業的服務

    全國咨詢熱線
    15990909037
    當前位置:首頁 »資訊中心 » 行業動態 » 電梯不銹鋼門套具體安裝制作過程

    電梯不銹鋼門套具體安裝制作過程

    來源:http://www.heartbeat-lb.com/ 瀏覽:發表時間:2022-06-21
    根據設計圖紙檢查門的規格、開啟方向、相關配件等。
    Check the specification, opening direction and relevant accessories of the door according to the design drawings.
    用卷尺量門洞的高與寬。門的標準高寬尺寸是200cm×80cm;衛生間的門高寬是200cm×70cm。尺寸如有出入要及時糾正。
    Measure the height and width of the door opening with a tape measure. The standard height and width of the door is 200cm × 80cm; The height and width of the toilet door is 200cm × 70cm。 If there is any discrepancy in size, it should be corrected in time.
    測量位置線,確定門框的位置,用墨斗彈拉出垂直線,一側門洞兩條垂直線。
    Measure the position line, determine the position of the door frame, pull out the vertical line with an ink fountain, and two vertical lines of the door opening on one side.
    在垂直線上用沖擊鉆打眼,孔眼與孔眼之間的距離約為30cm,一側門兩排共10個孔眼。沖擊鉆的鉆頭應為12mm,所鉆孔眼深度約為6cm。
    Drill holes on the vertical line with an impact drill. The distance between the holes is about 30cm. There are 10 holes in two rows of one side door. The drill bit of impact drill should be 12mm, and the depth of the drilled hole is about 6cm.
    將小木楔用鐵錘逐個釘入孔眼,以便固定門框板。小木楔的體積大小為5cm×1.5cm×1.5cm,以落葉松制作的為好,因為落葉松的木質結構緊,不容易松動。
    Hammer the small wooden wedges into the holes one by one to fix the door frame plate. The volume of the small wooden wedge is 5cm × 1.5cm × 1.5cm, it is better to make larch, because the wood structure of larch is tight and not easy to loosen.
    開料制作門框。左右做兩側門框龍骨的木工板尺寸為200cm× 3cm×8cm,門框頂龍骨的木工板尺寸為80cm×3cm×8cm。將高密度九厘板涂膠粘在龍骨上,再用釘固定。
    Cut materials to make door frames. The dimension of the wood board used to make the keels of the door frames on both sides is 200cm ×  3cm × 8cm, the dimension of the wood board of the keel on the top of the door frame is 80cm × 3cm × 8cm。 Glue the high-density 9cm board on the keel and fix it with nails.
    將制作好的三條門框按門的形狀連接起來,并且用大釘子在接合處固定。
    Connect the three fabricated door frames according to the shape of the door, and fix them at the joint with big nails.
    用刨子將連接好的門框表面修平整,修整邊角,棱角分明。
    Use a plane to flatten the surface of the connected door frame, trim the edges and corners, and make the edges and corners clear.
    將門框放到門洞上,按墻面的水平線為準,門框下拿木頭或者磚頭墊起,調節門框的高度。下面預留5cm埋在地板的龍骨中。
    Put the door frame on the door opening, subject to the horizontal line of the wall, take wood or bricks under the door frame to pad up, and adjust the height of the door frame. 5cm is reserved below and buried in the keel of the floor.
    在門框的上面釘一個釘子,把線垂掛上,通過線垂來調整門框的垂直,一邊衡量一邊用麻花釘將門框固定在門洞上。
    Nail a nail on the door frame, hang the line vertically, adjust the verticality of the door frame through the line sag, and fix the door frame on the door opening with fried dough twist nails while measuring.
    制作門臉的線條。門臉可以是現成買的,也可以是施工人員按照圖紙做出來的。制作完成后,就把門臉固定到門框上六,這樣門套就基本完成了。
    Make the lines of the door face. The facade can be bought off the shelf or made by the construction personnel according to the drawings. After making, fix the door face to the door frame six, so that the door pocket is basically completed.
    把門放到門套上比劃好,確定合頁在門套上的具體位置,再按合頁的厚度切出口徑。也切出鎖套的口徑。將門安裝到門套上,合頁用鑼絲刀將鑼絲釘擰緊。注意門與門套的間隙不得大于1.5mm,以順暢開關門為準。
    Put the door on the door pocket, make a comparison, determine the specific position of the hinge on the door pocket, and then cut the caliber according to the thickness of the hinge. Also cut out the diameter of the lock sleeve. Install the door on the door pocket, and use a gongs knife to tighten the gongs and screws on the hinge. Note that the gap between the door and the door pocket shall not be greater than 1.5mm, subject to the smooth opening and closing of the door.
    清除門套表面的附著物及灰塵,然后涂膩子。在涂膩子前先在門臉與墻面之間貼上美文紙,防止噴涂油漆時沾到墻面上。涂膩子時一定要均勻,修補好門套上釘眼。
    Remove the attachments and dust on the surface of the door pocket, and then apply putty. Before applying putty, paste paper between the door face and the wall to prevent it from sticking to the wall when spraying paint. The putty must be applied evenly, and the nail holes on the door jamb must be repaired.
    噴涂油漆。油漆噴涂效果會更加細膩一點,而細部可用刷子涂刷。
    Spray paint. The paint spraying effect will be more delicate, and the details can be brushed with a brush.
    將鎖安裝到鎖孔上,小心不要弄壞油漆。
    Install the lock on the lock hole and be careful not to damage the paint.
    電梯不銹鋼門套起到了固定門扇,同時對墻角進行保護的作用,并且還能發揮良好的裝飾性效果,是當前相當受歡迎的一種門套。制作安裝的過程上面已經介紹非常詳細了,每一步都有相應的要求,精心制作出來的門套,不僅質量好,而且裝飾性效果也不錯。
    The stainless steel door pocket of elevator plays the role of fixing the door leaf, protecting the wall corner at the same time, and can also play a good decorative effect. It is a very popular door pocket at present. The production and installation process has been introduced in great detail above, and each step has corresponding requirements. The carefully made door pocket is not only of good quality, but also of good decorative effect.
    以上就是為大家介紹的有關不銹鋼電梯門套的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務.http://www.sdjnjingguan.com
    The above is a detailed introduction about the stainless steel elevator door pocket. I hope it will help you If you have any questions, please contact us We will provide you with professional service http://www.sdjnjingguan.com
    337P人体艺扒开大腿
    <td id="0mk8k"><table id="0mk8k"></table></td>
  • <xmp id="0mk8k">
  • <menu id="0mk8k"><strong id="0mk8k"></strong></menu><xmp id="0mk8k"><menu id="0mk8k"></menu><nav id="0mk8k"></nav>